#PKA PACKET TRACER LABS FOR TABLET MANUAL#
#PKA PACKET TRACER LABS FOR TABLET PASSWORD#
#PKA PACKET TRACER LABS FOR TABLET PC#

For those pings to be successful, a default gateway must exist to route traffic from one subnet to another.Д¬lose configuration window Part 2: Create VLANs and Assign Switch Ports Pings were unsuccessful when trying to ping a device on a different subnet. If you answered no to any of the above questions, why were the pings unsuccessful? Note : It may be necessary to disable the PCs firewall to ping between PCs.

#PKA PACKET TRACER LABS FOR TABLET PC#

Verify that the PC hosts can ping one another. Refer to the Addressing Table for PC host address information.

Save the running configuration to the startup configuration file.Д¬lose configuration window Step 3: Configure PC hosts.

Shut down all interfaces that will not be used.

Configure the IP address listed in the Addressing Table for VLAN 1 on the switch.

S 2 (config)# banner motd $ Authorized Users Only! $ S1(config)# banner motd $ Authorized Users Only! $

Create a banner that warns anyone accessing the device that unauthorized access is prohibited.

S 2 (config)# service password-encryption

#PKA PACKET TRACER LABS FOR TABLET PASSWORD#

Assign cisco as the vty password and enable login.

Assign cisco as the console password and enable login.

Assign class as the privileged EXEC encrypted password.

Disable DNS lookup to prevent the router from attempting to translate incorrectly entered commands as though they were host names.

Console into the switch and enable privileged EXEC mode.

Step 2: Configure basic settings for each switch. Step 1: Cable the network as shown in the topology.ДЄttach the devices as shown in the topology diagram, and cable as necessary. In Part 1, you will set up the network topology and configure basic settings on the PC hosts and switches. Instructions Part 1: Build the Network and Configure Basic Device Settings

Ethernet cables as shown in the topology.

Console cables to configure the Cisco IOS devices via the console ports.

2 PCs (Windows with a terminal emulation program, such as Tera Term).

2 Switches (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable).

#PKA PACKET TRACER LABS FOR TABLET MANUAL#

If you are unsure contact your Answers.ДЄnswers Note : Refer to the Answers Lab Manual for the procedures to initialize and reload devices. Note : Ensure that the routers and switches have been erased and have no startup configurations.

Refer to the Router Interface Summary T able at the end of the lab for the correct interface identifiers. Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in th e labs. Other routers, switches, and Cisco IOS versions can be used. Note : The switches used with CCNA hands-on lab s are Cisco Catalyst 2960s with Cisco IOS Release 1 5.2(2) (lanbasek9 image). In this lab, you will create VLANs on both switches in the topology, assign VLANs to switch access ports, verify that VLANs are working as expected, and then create a VLAN trunk between the two switches to allow hosts in the same VLAN to communicate through the trunk, regardless of which switch the host is actually attached to. Trunks allow the traffic from multiple VLANS to travel over a single link, while keeping the VLAN identification and segmentation intact.

VLAN trunks are used to span VLANs across multiple devices. In general, VLANs make it easier to design a network to support the goals of an organization. VLANs can also be used as a security measure by controlling which hosts can communicate.

Modern switches use virtual local-area networks (VLANs) to improve network performance by separating large Layer 2 broadcast domains into smaller ones. Part 5: Delete the VLAN Database Background / Scenario Part 4: Configure an 802.1Q Trunk between the Switches Part 3: Maintain VLAN Port Assignments and the VLAN Database Part 2: Create VLANs and Assign Switch Ports

Part 1: Build the Network and Configure Basic Device Settings

Pka packet tracer labs for tablet